New Old Stock, Quantity 1 0708-087-1496

Product Overview: The Telesis® TMM4200 PINSTAMP® is a high-speed, multipin marking system that permanently prints messages into a variety of materials such as steel, aluminum, and plastic. Hardened pins are pneumatically accelerated to indent dot matrix characters into the item being marked. The shape, size, density, and location of characters are determined by the user through the system software. The marking head moves the pin cartridge through X- and Y-axis motions to reach the correct position for each dot of thecharacters to be marked. The system software automatically controls pneumatic pin extension and retraction to mark the message. The TMM4200 Marking Head includes the mechanical motion components to position the marking pins at precise X/Y positions and the pneumatic components to drive the marking pins from, and return the pins to, the pin cartridge. A shield plate around the pin cartridge assembly helps prevent debris from entering the marking head cavity. The TMM4200 marking head is an X/Y-traversing mechanism. Using two stepper motor drives, it accurately positions the pin cartridge at coordinate-defined locations in marking window within .008mm (in Fine mode) and .032mm (in Standard mode). The TMM4200 uses a rack-and-pinion drive system to rapidly position the pin cartridge and to accommodate the rigorous dynamics of impacting and rebounding. The floating pin design permits consistent, high-quality marks, even on irregular, slightly curved surfaces. It also accommodates applications where marking surfaces cannot be positioned at a consistent distance from the marker. TMM4200 Configurations include a hand-held version and a fixture-mounted version. The hand-held marker is available for portable operation. It incorporates a pistol grip handle with a push button trigger switch and an integral standoff to position the marker against the marking surface. The fixture-mounted unit is available for mounting in a fixed location. Pin Cartridges. The standard system uses non-lubricated, lightweight pin cartridges for the 25S-series and 150SA-series pins. Cartridges for 25S pins are available in two configurations: four (4) pins spaced on 6mm centers or on 12mm centers. The cartridge for 150SA pins contain two (2) pins spaced on 25mm centers. The cartridge configuration dictates the size of the marking window along the X-axis. Marking Pins. The TMM4200 uses 25S-series and 150SA-series marking pins available in various cone (tip) angles. The 25S-series pins are made of powdered steel stainless steel with diamond tips or carbide. The 150SA pins are made of powdered steel or tool steel with carbide tips. The Marker Cable connects the marking head to the controller. The highly flexible cable is 4m (13.1 ft.) long and attaches to the back of the marker with a quick disconnect connector. Optional extension cables lengths are available. The Filter/Regulator Unit includes two regulators with pressure gauges to control drive air and return air. The first regulator contains a filter to help remove contaminants from the supply air. Two air lines connect the regulated air to the marking head. Drive air fires the impact pin; return air pushes it back into the cartridge. Standard air lines are 4m (13.1 ft.) long made of 6mm tubing. TMC470 Controller provides the electrical interface and software control of the TMM4200 marking head. Product Features: System Setup: • Fixture-mounted markers only. When designing a fixture, allow for 3-axis adjustment to aid in horizontal, vertical, and lateral alignment of the marking head. Mount marking head to a suitable fixture using four M5-0.80 bolts. • Mounting bolts must not extend into marking head more than 10mm (0.39 in.) • Mount filter/regulator assembly, using brackets provided, within 4m (13.1 ft.) of marking head • Connect drive air and return air lines to the connectors on back of marking head • Connect supply air to input port on filter/regulator assembly • The TMC470 is not a sealed unit. Protect it from potentially damaging conditions and contaminants. Do not block vents in bottom of case. Ensure the marking system is electrically isolated from any devices that may generate extreme electromagnetic interference (EMI). • Locate controller as close as practical to marking head. Standard marker cable length is 4 m (13 ft.) • Install the controller as a table-top, wall-mounted, panel mounted, or enclosure-mounted unit, as applicable • Ensure controller power switch is OFF • Connect marker cable to controller • Connect power cable to controller • Position controller power switch to ON • Start marking system software • Adjust pin stroke, drive air, and return air for impact depth • Nominal drive air pressure 5.5 bars (80 psi) • Nominal return air pressure 1.5 bars (20 psi) System Options: • Standoff V-Block Kit (Hand-held markers only) • Standoff Hanger Kit (Hand-held markers only) • Tool Post Assembly • Marking Head Extension Cables • TMC470 Controller Wall-mounting Bracket Kit • TMC470 Controller Panel-mounting Bezel/Bracket Kit • TMC470N NEMA® Enclosure • Bar Code Scanner or Bar Code Wand with Cable • Foot Switch (Start Print) or Pushbutton Station (Start/Abort) • Backup Utility Software • Upgrade Utility Software • Logo/Font Generator Software General: Manufacturer: Telesis Model Name: Pin Stamp Marking System Model Number: TMM4200 Inventory Number: 0708-087-1496 Specifications: Rating: NEMA®2 (I.P. 41) Operating Temperature: 0° to 50°C (32° to 122° F), non-condensing Air Supply: Clean and dry, 4.2 to 8.3 bars (60 to 120 psi) Air Consumption: 0.15 L/sec (0.32 SCFM) idle, 0.28 L/sec (0.60 SCFM) marking Pin Types: 25S-series, various cone (tip) angles 150SA-series, various cone (tip) angles Pin Material: Powdered Steel or Stainless Steel with Diamond Tips or Carbide (25S-series), Powdered Steel or Tool Steel with Carbide Tips (150SA-series) Weight (lb): 12 lbs. Bay: D001 Aisle: EBA